Starting Your Mig-21

Post and comment on screen captures from the beautiful game here. Home of the monthly screenshot competition

Postby SeanTK » Wed Jul 06, 2011 11:52 am

Numerous heavy images, so it may take a while to load on slow connections!!!!



Welcome to the FSX Mikoyan-and-Gurevich Design Bureau MiG-21MF Fishbed!

This cockpit guide and startup checklist should aid you in manually starting up your Mig-21 from a cold and dark state, WITHOUT using Ctrl-E or the quickstart option.




Cockpit Familiarization








These labels are from memory without current sim access, but almost all of them should be correct, although the precise technical term may not be used. I could not remember the specifics of some of the many switches on the right panel, but they all need to be activated, so just go with that!


Let's begin:


Start by pressing "Shift + 2" to bring up the following menu:


Press the buttons to activate the chocks, ladder, pilot, and starter vehicle.

Left to right, the buttons are: chocks, ladder, pilot, starter vehicle, quick start key, helmet visor up/down, pilot model old/new.

You should now have the chocks, ladder, pilot, and starter vehicle visible in various sim views, such as the spot view.
Your "brakes" message should appear in the sim when the chocks are on.


Systems:

Cycle the shutoff switch on the left side of the cockpit. Don't leave it on, just cycle it to ensure your throttle is at idle.

Next, turn on almost everything on the right side of your cockpit. Batteries, alternator, generator, and all systems.

You can leave the gunsight, nav lights, and SPRD system switches off if you desire.

All other switches that you see on the above screenshot of the right side of the cockpit MUST be on!

At this time, if you wish, you can set your munitions and NDB/ADF frequencies. Munitions (drop tanks, missiles, rockets, show in spot view)
The NDB frequency box allows you to pre-set NDB frequencies that you will use through your flight. Upon closing this menu, the frequencies will show up on a placard on the right side of the cockpit, and all you have to do is press the button corresponding to your desired frequency. It's a very neat system!



Move to the left side of the cockpit!

Turn on the aileron boost switch!

Turn on all of those engine system switches!

Nose cone to automatic (abtomat)

Starter selector switch in the upper most position! (IMPORTANT!)

Press the starter button!


........................

Your Engine N2 RPM should rise and hover around 19% for a few seconds.

It will then kick over and start up very rapidly.

Your engine will idle at.........N1 = approx 37%.......N2 = approx 57%.


-----------------------------------
Visual indications that your engine has started.
---------------------------------
1. Red and yellow caution lights will extinguish (go out).
2. Smoke will stop spewing from the plane in spot view.
3. You are able to full adjust engine output with the throttle with minimal hesitation.
4. The engine will not fail when the truck is disconnected.



....at this time...your engine should have stabilized.

Disconnect the starter truck.

Make sure you are at idle, and release the chocks and ladder.

Pitot heat on! (Switched directly in front of joystick on lower central panel. Coloured gray.)

Lights on as desired. Taxi light is the upper most position on the marked switch on the left side of the cockpit.
Nav light 3 position switch (brightness) is on right side of panel. Upper most position is dimmest for daytime ops.

Lower flaps one notch to take-off position.

Set transponder to appropriate setting if needed (shift + 3 or 4 has default radio stack for convenience. One of those options also has default GPS for convenience.)

TRIM! Takeoff (and landing) trim will be correct when the marked green light illuminates in your annunciation box.
.....................


Taxi out! Check your brakes.

Turn on gunsight if desired.

Line up with runway.

Verify trim is set for takeoff (illuminated light.)


When trimmed properly, the aircraft should lift off of the ground on it's own at about 190 knots. You can help it up earlier at about 160 knots if you wish.

Enjoy your flight!
Hold brakes until passing 90% on the throttles, then release and off you go!



EDIT/NOTICE: The drogue chute release button is actually the other white button near the flaps switches further back on the left side. I picked the wrong one!
Last edited by SeanTK on Thu Jul 07, 2011 5:11 am, edited 1 time in total.
User avatar
SeanTK
Senior Member
 
Topic author
Joined: Sun Feb 28, 2010 9:27 am
Posts: 1617

Postby SeanTK » Wed Jul 06, 2011 12:06 pm

Let me know if anything is unclear or if you have any questions.
While the fact is that I can do a manual start up just fine, the question remains whether or not I can lead someone else through it without forgetting obvious stuff that has become automatic to me! smile.gif
User avatar
SeanTK
Senior Member
 
Topic author
Joined: Sun Feb 28, 2010 9:27 am
Posts: 1617

Postby Ian Warren » Wed Jul 06, 2011 1:24 pm

Thanks Sean biggrin.gif , I was going to phone Johny , hes Czech but no good with aircraft , fact is he hates warjets as he called them ohmy.gif .
Image
User avatar
Ian Warren
NZFF Pro
 
Joined: Fri May 05, 2006 5:23 pm
Posts: 41187
Location: AREA 51

Postby Olderndirt » Wed Jul 06, 2011 1:49 pm

Sean
An excellent piece of work. On my next flight I hope not to have the umbilical connection with the APU truck.
Image
User avatar
Olderndirt
Senior Member
 
Joined: Wed Jan 05, 2011 2:36 pm
Posts: 1774
Location: Rochester, Washington USA

Postby J7G » Wed Jul 06, 2011 10:04 pm

That's a HUGE help, thanks very much!
User avatar
J7G
Forum Addict
 
Joined: Wed Feb 23, 2011 8:49 pm
Posts: 449

Postby Splitpin » Wed Jul 06, 2011 10:18 pm

Awesome work Sean.....5 stars thumbup1.gif
User avatar
Splitpin
NZFF Pro
 
Joined: Mon Aug 03, 2009 12:15 pm
Posts: 21333
Location: Christchurch NZ

Postby SeanTK » Thu Jul 07, 2011 5:10 am

Just one little fix so far from a tester. The drogue chute release switch is the white button near the flaps buttons. I picked the wrong one!
Luckily, it's not life threatening!
smile.gif
User avatar
SeanTK
Senior Member
 
Topic author
Joined: Sun Feb 28, 2010 9:27 am
Posts: 1617

Postby Adamski » Thu Jul 07, 2011 11:46 am

*Great stuff* Sean!! That's cleared up a few mysteries for me - particularly the nose-cone and the trim. I'm printing this one out and binding it winkyy.gif

It really is a stunning FREE add-on. Just waiting for some more repaints!
Image
User avatar
Adamski
NZFF Pro
 
Joined: Thu Nov 01, 2007 2:22 am
Posts: 5029
Location: Birkenhead, Auckland

Postby SeanTK » Fri Jul 08, 2011 4:34 am

Gentlemen, we have a working SPRD/JATO system now!

http://www.migsim.ic.cz/sprd.html
User avatar
SeanTK
Senior Member
 
Topic author
Joined: Sun Feb 28, 2010 9:27 am
Posts: 1617


Return to Screenshots

Who is online

Users browsing this forum: No registered users and 17 guests